- 728 -
gbl005 thru gbl10 single phase 4.0 amps. glass passivated bridge rectifiers voltage range 50 to 1000 volts current 4.0 amperes f eatures glass passivated chip junction ideal for printed circuit board high case dielectric strength plastic material has underwriters laboratory flammability classification 94v-0 typical ir less than 0.1 a high surge current capability high temperature soldering guaranteed: 260 o c / 10 seconds / .375?, (9.5mm) lead lengths. m echanical data case: molded plastic body. terminals: plated leads solderable per mil-std-750, method 2026. weight: 0. 071 ounce, 2.0 grams mounting position: any gbl dimensions in inches and (millimeters) m aximum ratings and electrical characteristics rating at 25 ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20% type number symbol gbl 005 gbl 01 gbl 02 gbl 04 gbl 06 gbl 08 gbl 10 unit s maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms voltage v rms 35 70 140 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v maximum average forward rectified current @t c = 50 (note 1) @t a = 40 (note 2) i (av) 4.0 3.0 a peak forward surge current, 8.3 ms single half sine-wave superimposed on rated load (jedec method ) t j =150 i fsm 150 a maximum instantaneous forward voltage @ 4.0a v f 1.00 v maximum dc reverse current @ t a =25 at rated dc blocking voltage @ t a =125 i r 5.0 500 ua ua typical thermal resistance per leg (note 1) (note 2) r ja r jl 22 3.5 /w typical junction capacitance per leg at 4.0v, 1mhz cj 95 40 pf operating temperature range t j -55 to +150 storage temperature range t stg -55 to + 150 notes 1. unit mounted on 2? x 3? x 0.25? al. plate. 2. units mounted on p.c.b. 0.5? x 0.5? (12x12mm) copper pads, 0.375? (9.5mm) lead length.
- 729 - ratings and characteristic curves (gbl005 thru ) gbl10 fig.1- derating curve for output rectified current 50 number of cycles fig.2-maximum non-repetitive peak forward surge current per leg fig.3- typical forward voltage characteristics per leg instantaneous for ward current . (a) fig.4- typical reverse leakage characteristics per leg instantaneous reverse current .( a) leakage 150 100 0 1 100 10 1 10 0.1 0.01 10 1 0.4 0.6 0.8 1.0 1.2 1.4 02040 60 80 100 instantaneous forward voltage. (v) percent of rated peak reverse voltage. (%) tj=25 c 0 tj=125 c 0 tj=40 c single half sine-wave (jedec method) o 1 cycle ambient temperature. ( c) o peak for ward surge current . (a) average for ward current .(a) rectified 50 100 0.1 0.01 1.0 0 2.0 3.0 4.0 5.0 0 fig.5- typical junction capactitance per leg reverse voltage. (v) 0.1 1 10 100 junction cap acitance ( ) pf tj=25 c f=1mhz vsig = 50mvp-p 10 100 1000 50 400v 600 1000v tj=25 c pulse width=300 s 1% duty cycle 500 50 400v 600 1000v 100 150 p.c.b. mounting 0.47 x 0.47" (12 x 12mm) copper pads with 0.375" (9.5mm) lead length heat-sink mounting 2.0 x 3.0 x 0.25" aluminum substrate 60 hz resistive or inductive load 100 1.6 0.1 1 10 100 0.01 10 1 100 0.1 t, heating time (sec.) transient thermal impedance ( c/w) fig.6- typical transient thermal characteristics
|
